How to Reset Waste Ink Counter Canon Pixma iX5000 and iX4000 - Absorber Full

To reset Absorber Full for Canon PIXMA iX4000 or iX5000 you have to enter to service mode. Follow the step to enter to service mode on Canon PIXMA iX4000 or iX5000 :

1. Connect the Canon PIXMA iX5000 or iX4000 printer to the power cord. ( note : If the automatic power-on function is enabled in the printer, the printer enters the service mode for the first time, but it will never enter the service mode if the printer is turned off by the Power button. This is because the printer remains to be turned on internally if the power is turned off by the Power button. To prevent this, disconnection of the power cord is required before starting the printer in the service mode ) .
2. With the Canon PIXMA iX5000 or iX4000 printer powered off, while pressing the Resume/Cancel button, press and hold the Power button. (note : Don’t release the buttons. The Power LED lights in green to indicate that a function is selectable.)
3. While holding the Power button, release Resume/Cancel button. (Don’t release the Power button.)
4. While holding the Power button, press Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons.
5. When the Power LED lights in green, press the Resume/Cancel button 4 times to reset waste ink counter in the Canon Pixma iX5000 / iX4000. (note : If the Power LED does not light in green the printer does not enter the service mode, disconnect the power cord and plug it again. Then start from step 1 to start the printer in the service mode again).
6. At the end of the service mode, press the Power button. The paper lifting plate of the sheet feed unit will be raised.
   

Note :

• Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.

How to reset waste ink Canon Pixma MP145 - Absorber Full

Solution:

• Connect the printer to a Power source.
• Turn off the printe.
• With the Printer power off, press the "Power" button while press and hold Stop/Reset button.
• When the Power led is light, press "Stop/Reset" button two times while pressing and holding the "Power" button.
• When releasing the "Power" button and the "Stop/Reset" button, the printer will move into a service mode
• When the on/off lights in green, press the "Stop/Reset" button four times to reset wase ink counter.
• Unplug cable power from a power source.

Service Printer Canon i90 - Waste Ink Tank Full

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

5) Press the Power button. The LED lights in green, and the

selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6) Power off then back on and test.

Printer Canon Pixma MP258 – Absorber Full

Printer Canon Pixma MP258 – Absorber Full

If your printer show P07 error it means that your ink absorber inside the printer is almost full. In order to solve this you need to clear or reset the counter protection of your printer. To do this, follow this steps.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS:  Entering Service Mode

You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.

2. Hold down STOP/RESET button and press Power button.

3. Keep holding down Power button and let STOP/RESET button go.

4. Then Press STOP/RESET button twice then let BOTH buttons go.

5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"

2. Load some papers in your printer and press the "Main" Button once, wait until the printing is done.

3. Then press "EEPROM Clear" button to clear EEPROM.

4. Then press EEPROM button and the printer will print some text.

5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

GFCH5V82RBB9 

Printer Canon Pixma MP258 – Error P08

First time, I found the problem Canon Pixma MP258 printer will not print from the cpu or the Copy Scan and P08 are the error messages on the printer panel. I could maybe try to reset, e turned out to be, then I created to copy directly, it was also error.

I've lost both cartridges, the ink was discharged, directly, I refill the black  and a color cartridge. Then I do a test print and the result is smooth and good wow.

If this error P08 does not clear, please 

Follow the instructions step by step

1. Turn off printer, cable power still plug in,
2. Press Stop/Reset button  don't release
3. Press Power Button don't release and than release Stop/Reset button
4. Press Stop/Reset button 2X and than release Power Button, wait until service mode to " 0 "
5. Turn off printer, cable power still plug in
6. Press Stop/Reset button  don't release
7. Press Power Button don't release and than release Stop/Reset button
8. Press Stop/Reset button 4X and than release Power Button, wait until service mode to " 1 "
9. Turn off printer, and loose cable power, wait one minute.
10. Connect cable power, turn on printer again, now this printer ready to use.

Reset Catridge Empty on Canon MP198

Sometimes, after you filling up the printer cartridge with the ink, there is error message that the printer still can't run due to empty cartridge. It will make a question, why after re-fill the cartridge, the printer can't run..?

To solve this error, your cartridge need to be reset. Just push and hold the reset button for about 5 seconds and your printer will run properly. In some cases, you need to take out the cartridge and then plug the cartridge again.

Reset Epson TX720WD

Adjustment program for Printer Epson Stylus Photo TX720WD.

Download TX720WD resetter.

Good luck ;)