Reset Canon MX308

Step by step reset Waste Ink Absorber Full printer Canon MX308.

Run Service Mode:

• Press and hold "Stop/Reset" and the "Power" buttons.
• Release the "Stop/Reset" button.
• Press the "Stop/Reset" button twice, (still holding the "Power" button).
• Release the "Power" button. Your printer is now in Service mode

Reset:

• Insert paper into the paper tray.
• Press "Stop/Reset" button 4 times, this will select the clear waste ink counter function.
• Press the "Power" button to turn off the printer.

If it does not work, try this after "Run Service Mode":

• Insert paper into the paper tray.
• Press "Stop/Reset" button 1 times then press Power botton, wait until printing finish.
• Press "Stop/Reset" button 2 times then press Power botton. wait until printing finish.
• Press "Stop/Reset" button 3 times then press Power botton.
• Press "Stop/Reset" button 4 times then press Power botton.
• Press the "Power" button to turn off the printer.
• The printer will now work normally.

Reset ink level printer Canon MX308

Step by step reset the ink level printer Canon MX308, also work fine on other canon MX300 series.

• Disconnect power cable
• Connect it while holding down the power button.
• With the power button still down, press twice the "Cancel/Stop" red button.
• Release power button.
• Printes turns into a kind of factory mode (wait for about 10 seconds, untils it says “Idle”)
• Press ">" (next to "OK" button) once "Shipping Mode 3"
• Press "OK" button.
• Press "OK" again for "Without cleaning"
• A test page will print.
• Open printer cover, like you are about to change the cartridges.
• Disconnect the power cable again.
• Take out both cartridges.
• Close printer cover.
• Connect power cable once again.
• Turn printer on.
• Put the cartridges back

EPSON RX500 reset procedure

Protection counter is the counter for wasted ink; it says to printer how much space it has in special tray where all wasted ink are going during cleaning procedures. With time it became full (printer just won't print in this case) and absorbtion padding must be replaced. After replacing the padding You must reset the protection counter to zero in order to continue ordinary printing.

EPSON RX500 reset procedure

Press all following buttons :Power, Load/Eject, Stop, B&W, Color,
after this printer turns on and you'll see "Init eeprom" on printer screen.
Press Color button to clear protection counter.

Alternate. Hold down "clear + setup + on"
Continue to hold the buttons until the printer had powered on, then off again, then back on. Once you noticed that the LCD had flashed a blank screen, let go of the 3 keys. In the LCD window you now have access to 3 options using the select keys.

Look for an abbreviation resembling "ink pad level" . Here is where Held down the clear button for around 10 seconds. LCD must read "Press Power to Reset."

Epson CX6500 reset procedure

Epson CX6500 reset procedure

• Press and hold (B&W+COLOR+STOP)
• Press POWER
• Press COLOR
• Turn off printer
• Then turn on the printer.

Resetter Canon iP1600

Waste Ink Counter Reset.

Step 1 : Manual Temporary
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect the printer cable.
4. Close door, then release power button.

step 2 : Software iP1600ServiceTool for Permanant
1. Open General Tools software
2. Select (USB PORT)
3 .Click DEVICE ID
4. Select EEPROM CLEAR
5. Click TEST PATTERN 1
6. Turn off the printer

Reset cx6500

How to reset Epson CX6500 or any multifunction:

• Press and hold B/W+COLOR+STOP


• Push power on button, don’t release all the button until you see the light indicator is blinking and then a message display on the LCD


• Release your fingers from the button


• Press the COLOR button to clear protection counter


• Press power button (turn off)


• DONE!

Reset Canon i6100

Reset Canon i6100

• Turn off the printer.
• Press and hold the RESUME button, then press and hold the POWER button.
• Release the RESUME button, next press and release the RESUME button two(2) more times in succession, then release the POWER button.
  
• Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.
  

1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM – Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!)
   

MPC 110 RESET PROCEDURE

How to reset MPC 110/130
* Turn On the printer
* Press "MENU - SCAN - COPY - SCAN"
* Press +
* NVRAM ACCESS press OK
* Press -
* SET ABS-P LEVEL press OK
* Reset level press +
* Press OK
* Press -
* SET ABS-M LEVEL press OK
* Reset level press +
* Press MENU and EXIT
* Turn off the printer

Reset Canon iP 1880

This is how to reset Canon iP 1880 :
1. Press Resume button and hold for 1 - 2 minutes
2. Open the cover
3. Release the catridge and then put them on again
4. Close The Cover
5. Turn off the printer
6. Turn it on again.

Or you can use IPTool software to reset,
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
5. Open Iptool then klik "Reset Main"

Download IPTool

Canon mp150 reset codes

MP150/MP160 ERROR CODE
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full

E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

How to clear E27 Code

• With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
• When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
• When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
• When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

• Turn off the printer.( it must be turn off) then turn it on again.